Point Pod Boardroom raised in a long timber boardroom table, showing two power points, USB and data ports, in a glass-walled Sydney office

Guide · Boardroom tables · Australia

Boardroom Table Power: What to Plan Before an Office Fitout

Power, data and HDMI at the meeting table are simple to plan early, and expensive to add once the floor and the table are in.

By Seb Aroney, founder of Modern Power Solutions · Updated November 2026

Free shipping across AustraliaShips in 24 hoursUp to 4-year warranty1,800+ reviews

Quick answers

?How do you get power to a boardroom table?Up through the floor. A floor box under the table feeds a pop up unit in the tabletop, through a table leg or cable tray. Wall points only suit tables against a wall, and a ceiling drop puts a pole in the room.
?Which table power unit suits a boardroom?One that sits flush when it’s closed. The Point Pod Boardroom rises at a press with two power points, USB-A, USB-C, HDMI and RJ45, and hides under a disc of your tabletop. The V14B-HNR adds a fourth power point and needs less room below.
?How much room does it need under the table?600 mm clear for the Point Pod Boardroom, measured from the top of the table, and 160 mm across for its flange. The V14B-HNR needs 220 mm, and the V14 160 mm.
?What has to be decided before the fitout?The table position first, then the units, the cable route, the data and AV ports and who cuts the table. The five decisions.
?Do I need an electrician?For the floor box, yes. A new power point is fixed wiring for a licensed electrician. The table units plug into it, so they need no wiring of their own.

Why power the table

Why boardroom tables need power, data and HDMI

Most meetings now run from a laptop. People need to charge, connect to the network and share a screen, often all at once. Putting those connections in the table means:

PowerNo power boards or extension leads on the floor, and no flat laptops halfway through a meeting.
DataA wired network connection for video calls that can’t afford to drop out.
HDMIPresent straight from the table, without running a cable to the wall.
USB-A and USB-CCharge phones and tablets without adaptors.

Where power comes from

Getting power to the boardroom table

In most boardrooms the power doesn’t come from the ceiling or the walls. It comes up through the floor.

Floor box: the usual answerSet into the slab or raised floor under the table. Power, data and AV come up through a table leg or cable tray to the unit in the tabletop, so nothing crosses the carpet.
Ceiling drop: rarely suitsPossible, but it puts a pole in the middle of the room, which rarely suits a meeting space.
Wall outlets: only against a wallThey only work for a table pushed against the wall, which boardroom tables usually aren’t.

A floor box power point is fixed wiring, so a licensed electrician installs it, to AS/NZS 3000. The table units then plug into it.

Glass-walled rooms

Why glass-walled meeting rooms make this harder

Glass walls can’t carry a power point, so in rooms built with office glass partitions the power has to come up through the floor and the table.

That makes the floor box position critical. It needs to sit under the table, clear of the table legs, and close enough that the cable run up into the tabletop is short and hidden.

If the table moves after the floor box goes in, you’re left with an exposed box or a cable across the carpet.

Fix the table position first, then place the floor box to suit it.

Point Pod Boardroom

The Point Pod Boardroom up close

The Point Pod Boardroom was made for meeting tables. Press the top and let go: an electric motor raises it 280 mm out of the table. Unplug everything, press again, and it lowers back down, flush with the tabletop.

Its top cup holds a 93 mm disc of your own table material, so when it’s closed only a slim ring and the matching insert show.

A few practical points before you order

Cut-outA 102 mm hole in the tabletop, plus a 93 mm insert up to 20 mm thick, cut from the same material. Our 102 mm hole saw cuts both in one go.
PowerTwo power points and the USB ports run from one 1.9 m lead with a 10 A plug, which goes to the power point in the floor box. 10 A (2400 W) in total.
Data and videoThe RJ45 and HDMI ports are pass-throughs, with matching ports underneath. Run your network and display cables to them, with enough slack for the 280 mm rise.
Under-table spaceThe body is 560 mm long when closed, so allow 600 mm clear below the top. Check it clears leg frames, modesty panels and cable trays.
Table thicknessAny thickness from 12.7 mm, with no maximum: the mounting flange fixes underneath. See our benchtop thickness guide.
FittingA collet lines the hole and a flange is fixed under the table. The unit drops in and clips to it, and is never glued. How to install a Point Pod.

Manual, dimensions and hole template

Point Pod BoardroomPoint Pod BoardroomManual MPS-UM-PPMBT-AU, the dimensions sheet and a 1:1 template for the 102 mm hole.Manual · PDFDimensions · PDFHole template · PDF

Before the fitout

What to decide before the fitout starts

1

Table size and position. The floor box goes where the table goes, so fix this first.

2

How many units, and where. Mark each unit on the table drawing, clear of legs, frames and modesty panels, with the clear space each one needs below the top.

3

The cable route. Decide how cables get from the floor box to each unit: up a leg, along a cable spine or in a tray under the top.

4

Data and AV. Tell your IT and AV installers which ports are at the table, so they run network and HDMI cables to the floor box and leave slack for the unit to rise.

5

Who cuts the table. Give the table maker the hole positions and sizes (102 mm for a Point Pod Boardroom) and ask them to cut the 93 mm inserts from the same material.

If you’re planning office fitouts in Sydney or anywhere else, lock in the floor box position before the flooring goes down. Getting these five things agreed early means the boardroom works on day one, without leads on the floor or holes cut in the wrong place.

Specs

Point Pod Boardroom at a glance

ModelPPMBTPoint Pod Boardroom, silver
Outlets2 power pointsPlus USB-A and USB-C, 2.1 A each
Data and videoHDMI and RJ45Pass-through, ports underneath
LiftMotorisedPress and release the top
Hole102 mmCut clean and chip-free
Insert93 mm acrossUp to 20 mm thick
Table12.7 mm or thickerNo maximum
Clear below600 mmMeasured from the top
Length560 mm closed840 mm open, rising 280 mm
Lead1.9 mWith a 10 A plug
Rating10 A, 2400 WIn total, with an overload switch
ApprovalGMA-504353-EA24-month warranty

Confirm the table thickness, the space under the table and the floor box position before the table is cut. The warranty is 24 months, and you can extend it to up to four years through our warranty promotion.

Questions

Boardroom table power FAQs

How do you get power to a boardroom table?

Through a floor box set into the slab or raised floor under the table, then up a table leg or cable tray to a pop up unit in the tabletop. A licensed electrician installs the floor box power point; the units themselves plug into it.

Can I get a boardroom table with power built in?

Yes. Any table maker can cut a round hole for a pop up unit: 102 mm for the Point Pod Boardroom or 120 mm for the V14 range. Give them the positions before the table is made, with the space each unit needs below the top.

What is the best power solution for a conference room table?

A unit that sits flush when it’s closed and gives people power, USB, data and HDMI when it’s open. The Point Pod Boardroom hides under a disc of your tabletop; the V14B-HNR suits tables with only 220 mm clear underneath.

How do you get power to a table in a glass-walled meeting room?

Through the floor. Glass walls can’t carry a power point, so place a floor box under the table, clear of the legs, and run the cables up through the table to the unit.

What size hole does the Point Pod Boardroom need?

102 mm, cut clean and chip-free, plus a 93 mm disc of the same material for the top, no more than 20 mm thick. Our 102 mm hole saw cuts the hole and keeps the disc in one cut.

How thick can the table be?

Any thickness from 12.7 mm, with no maximum: the Point Pod Boardroom’s mounting flange fixes underneath. Only the disc in the top is limited, to 20 mm. More in our benchtop thickness guide.

Are the HDMI and RJ45 ports powered?

No. They’re pass-through connections to matching ports under the unit. Plug your screen and network cables in underneath, with enough slack for the unit to rise 280 mm.

Is the Point Pod Boardroom approved for Australia?

Yes. Its electrical safety approval number is GMA-504353-EA, and we can send the certificate on request.

Planning a boardroom?

Email us your table drawing and we’ll check the Point Pod Boardroom suits it. Fitout companies and builders can order at trade prices.

Two pop up power points with stainless steel tops raised in a hotel room desk, charging a laptop
Back to blog
Seb Aroney, founder of Modern Power Solutions

About the author

Seb Aroney

Founder and Director, Modern Power Solutions

Seb has been developing pop up power points since 2013, and they're all Modern Power Solutions does: one specialist range for kitchens, islands and offices, sold across Australia, the US and the UK, with support and warranty handled by our own team.