Point Pod closed flush in a marble benchtop, with only a slim silver ring showing

Guide · Point Pod · Australia

The Point Pod: Pop Up Power Points That Hide in Your Benchtop

A motorised pop up power point that hides under a disc of your own benchtop. The four models, what each one needs and how it’s installed.

By Seb Aroney, founder of Modern Power Solutions · Updated November 2026

Free shipping across AustraliaShips in 24 hoursUp to 4-year warranty1,800+ reviews

Quick answers

?What is the Point Pod?A motorised pop up power point whose top is a disc of your own benchtop. Closed, only a slim ring shows; press the top and it rises with power points and USB. It’s designed and engineered in Australia by Point Pod.
?Which Point Pod should I get?The Compact for two power points, the Multi for three. The Compact with USB swaps one power point for USB-A and USB-C, and the Boardroom adds HDMI and RJ45 for meeting tables.
?How is a Point Pod installed?In a 102 mm hole, held from below. A collet is siliconed into the hole, a mounting flange is fixed underneath, and the Point Pod drops in and clips to it. It plugs into a power point in the cupboard. The steps.
?How much space does it need?450 mm clear below the benchtop for the Compact, 600 mm for the Multi and Boardroom, measured from the top surface, with a power point within reach of the 1.9 m lead.
?Where should it go on an island bench?Outside the sink and cooktop zones: at least 150 mm from the side of a sink of 40 litres or less (0.5 m for bigger sinks) and 150 mm from the cooktop, on an RCD-protected circuit.

How it works

A pop up that disappears into the benchtop

Press to raisePress the top and let go: a motor raises it 170 mm (Compact) or 280 mm (Multi and Boardroom). Unplug everything and press again to lower it.
Closes flushThe top cup holds a 93 mm disc of your benchtop, so when it’s closed only a slim ring and your stone or timber show.
Plugs in belowA 1.9 m lead with a 10 A plug goes to a power point in the cupboard, so the Point Pod itself needs no hardwiring.
Stays removableA mounting flange and fastening clip hold it from below. It’s never glued in, so it can always come out from under the benchtop.

Point Pod is designed and engineered in Australia, and its benchtop-insert design won a Good Design Award in 2019.

Models

The four Point Pods

Pick by how many power points you need and how much room there is under the benchtop.

All four take the same 102 mm hole and a 93 mm disc no more than 20 mm thick. Below = clear space under the benchtop, measured from the top.

Looking for Point Pod Connect (PPCV815 or PPCV815B)? That’s the US model, with US outlets, so it isn’t sold in Australia. The four models above are the Australian range.

Installing it

How a Point Pod is installed

Have a professional benchtop installer cut the hole and fit it. The six steps from the install manuals:

1

Check the space. 450 mm clear below the benchtop for the Compact (600 mm for the Multi and Boardroom), measured from the top surface, and 160 mm across for the flange. Keep drawers and pipes clear, with a power point within reach of the 1.9 m lead.

2

Make the insert. Cut a 93 mm disc of your benchtop, no more than 20 mm thick, and test-fit it in the top cup. Our 102 mm hole saw keeps the core from the hole whole for this.

3

Cut the hole. A clean, chip-free 102 mm hole, using the template in the manual. Stone needs a diamond core bit with water cooling, or a water jet. Cutting existing engineered stone must follow the WHS rules for silica dust.

4

Fit the collet and flange. Silicone the outer collet into the hole, flush with the top. Underneath, fix the mounting flange around it: two-part epoxy such as Megapoxy on stone, screws on timber.

5

Lower the Point Pod in. Feed it down through the collet until the top sits flush, then tighten the fastening clip onto the flange. Never glue the unit: it must stay removable.

6

Glue in the insert and test. Silicone the disc into the cup, lining up the pattern. Once it’s set, plug in and allow up to a minute to start: the first press moves it down, the next raises it.

Install manuals

Point Pod CompactPoint Pod CompactTwo power points · 170 mm raised · 450 mm clear belowSilver · PDFBlack · PDF
Point Pod Compact with USBPoint Pod Compact with USBOne power point, USB-A and USB-C · 170 mm raised · 450 mm clear belowSilver · PDFBlack · PDF
Point Pod Multi with USBPoint Pod Multi with USBThree power points, USB-A and USB-C · 280 mm raised · 600 mm clear belowSilver · PDFBlack · PDF
Point Pod BoardroomPoint Pod BoardroomTwo power points, USB, HDMI and RJ45 · 280 mm raised · 600 mm clear belowManual · PDF

Specs

Point Pod at a glance

Hole102 mmCut clean and chip-free
Benchtop12.7 mm or thickerNo maximum
Clear below450 mm600 mm for the Multi and Boardroom
Flange160 mm acrossFixed under the benchtop
Insert93 mm acrossNo more than 20 mm thick
Raised170 mm280 mm for the Multi and Boardroom
Rating10 A, 2400 WIn total, with an overload switch
USB2.1 A per portUSB-A and USB-C, on USB models
Lead1.9 mWith a 10 A plug
Supply230–240 VFrom a power point under the benchtop
ApprovalGMA-504353-EACertificate on request
Warranty24 monthsExtension available

Where it goes

Where to put a Point Pod on an island bench

The AS/NZS 3000 distances for a power outlet near a sink or cooktop, and what the circuit needs.

150 mm from the sinkFrom the side of a sink of 40 litres or less. For bigger sinks and tubs it’s 0.5 m.
150 mm from the cooktopNo power outlet within 150 mm of the edge of the cooktop.
On an RCD-protected circuit30 mA RCDs are required on household circuits, including the one the Point Pod plugs into.
A power point in the cupboardGetting power to the island means a power point inside the cupboard, fitted by a licensed electrician. The Point Pod plugs into it.

Are pop up power points legal in Australia? · Island power point guide

Everyday use

Living with a Point Pod

Starting upAfter plugging in, allow up to a minute for it to start. The first press moves it down; press and release again to raise it.
Lowering itRemove every plug, clear the top, then press and release. If something blocks it while it closes, it reverses. Never force it down.
Spills and crumbsLower it when you’re not using it and wipe up spills straight away. Crumbs that get in usually drop through the weep holes in the flange, so vacuum the cupboard below now and then.
CleaningWipe the ring and outlets with a soft, dry or slightly damp cloth, and clean the insert as you would the rest of your benchtop.
Service and swapsIt’s held by the fastening clip and never glued, so it can come out from under the benchtop for service or a swap.
Warranty24 months, parts and labour, with an extended warranty available.

See one

Find a Point Pod installer or showroom

See a Point Pod in person, or find someone near you who has fitted them before. Both maps open in Google Maps.

Questions

Point Pod FAQs

What is a Point Pod?

A motorised pop up power point designed and engineered in Australia by Point Pod. Its top holds a disc of your own benchtop, so when it’s closed only a slim ring shows.

How do you install a Point Pod?

Cut a 102 mm hole, silicone the outer collet into it and fix the mounting flange underneath. Then lower the Point Pod in, tighten its fastening clip, glue a disc of your benchtop into the top and plug it into a power point in the cupboard. Have a professional benchtop installer cut the hole.

What size hole does a Point Pod need?

102 mm, cut clean and chip-free. Underneath, allow 160 mm across for the mounting flange, and 450 mm clear below for the Compact (600 mm for the Multi and Boardroom).

How thick can the benchtop be?

At least 12.7 mm, with no maximum: the mounting flange fixes underneath. The disc in the top must be no more than 20 mm thick, so a thicker one is trimmed. For a thinner disc, raise the cup’s height-adjuster screws, then add a spacer if needed.

Is the Point Pod available in Australia?

Yes. It’s designed and engineered in Australia, and we sell all four models online with free shipping across Australia.

How do I get power to a kitchen island?

Have a licensed electrician fit a power point inside the island cupboard, on an RCD-protected circuit. The Point Pod plugs into it with its 1.9 m lead, so the Point Pod itself needs no hardwiring.

Where should power points go on an island bench?

At least 150 mm from the side of a sink of 40 litres or less (0.5 m for bigger sinks and tubs), and 150 mm from the cooktop. Our legality guide has the details.

What’s the difference between the Compact and the Multi?

The Compact rises 170 mm with two power points (or one plus USB-A and USB-C) and needs 450 mm clear below. The Multi rises 280 mm with three power points plus USB, and needs 600 mm.

Is the Point Pod spring-loaded?

No. It’s motorised: the built-in motor raises and lowers it when you press and release the top.

Is the Point Pod approved for Australia?

Yes. Its electrical safety approval number is GMA-504353-EA, and we can send the certificate on request.

Choosing your Point Pod?

All four ship free across Australia. Not sure a Point Pod is the right pop up for you? Our island guide compares it with the rest of our range, with a finder and a fit checker.

Black V3L pop up power point raised on a stone kitchen island
Back to blog
Seb Aroney, founder of Modern Power Solutions

About the author

Seb Aroney

Founder and Director, Modern Power Solutions

Seb has been developing pop up power points since 2013, and they're all Modern Power Solutions does: one specialist range for kitchens, islands and offices, sold across Australia, the US and the UK, with support and warranty handled by our own team.